PDA

Ver la Versión Completa : Resetear computadora de Honda Civic '02


Makillo
02-Jan-2007, 12:38
Hola Amigos alguien me podria decir como puedo resetear mi computadora a parte de quitar la bateria, tengo encendida la luz de las Bolsas de Aire solo porque pinte el carro y desconectaron los sensores, eso me ocasiono un codigo de bolsa estallada cosa que no es cierto.

Gracias.

crisaguilar
02-Jan-2007, 12:39
quitando la bateria la reseteas si no se quita con eso es por que te dejaron mal conectado algo :ok:

kike
02-Jan-2007, 12:58
Vos crisaguilar vos que sabes de esas ondas, al carro de mi viejo se le encendio la luz de service coming soon algo asi, es un sentra b15 automatico, ya desconectamos la bateria y no se apaga como podemos hacer para apagarla? ya que el carro ya se le hizo servicio y toda la onda

crisaguilar
02-Jan-2007, 13:32
uyy fijate que regularmete cando haces el servicio se apaga sola por los sensores de niveles (aceite agua, frenos etc.) y hay un boton para reiniciar eso en los hondas se donde esta pero en los sentra :asaber:

Makillo
02-Jan-2007, 13:46
quitando la bateria la reseteas si no se quita con eso es por que te dejaron mal conectado algo :ok:Gracias por tu respuesta, fijate que es curioso me paso con 2 hondas, los pinte completos y les paso lo mismo la AIR BAG encendida, o seran asi los Hondas????? yo personalmente revise que los sensores esten bien conectados pues en un inicio pense que los habian dejado desconectados pero en las 2 ocasiones estaban bien colocados, que otra cosa podra ser?????

GuateskateVTi
02-Jan-2007, 13:52
How to reset your SRS light on your civic. This works for 99-00 Civic's as well as 2k1's. What is pictured is actually a 2k1 but the plug for the 99-00's are in the fuse box also, just on the other side of the column.

1st you need to either buy or make the "SCS Service Connector." I used a speaker harness for and older Honda which you can buy at a local stereo shop such as Circuit City or Best Buy, and cut the wires and looped them together. You can also use a paperclip but that will make it a little more difficult because you have to connect it and disconnect it a few times quickly.

2nd you need to find the MES (Memory Erase Signal) connector which is pictured below:


http://www.knology.net/~jediklc/images/srsplug.jpg

MES Plug in Fuse box.
SCS Plug http://www.knology.net/~jediklc/images/scs1.jpg

It is a yellow connector with two wires in it that is plugged into the fuse box, unplug it and pull it down. Once you have done that you can begin the process of erasing the memory. NOTE: This will only reset your SRS System if what caused it to trigger has been fixed, Ex: turning the ignition on with any SRS Plugs disconnected, such as pulling your seat out.

1st step in erasing the memory is to turn the ignition off and connect the SCS Service connector to the MES Plug,

2nd Turn Ignition on. SRS indicator light will come on for about 6 seconds then go off.

3rd Disconnect SCS service connector for MES connector within 4 seconds after SRS indicator light goes off. SRS indicator light will come on again.

4th Reconnect SCS service connector the MES connector within 4 seconds after SRS light comes on. SRS indicator light will go off.

5th Disconnect SCS service connector from MES connector within 4 seconds. SRS indicator light will indicate that memory is erased by blinking 2 times.

6th Turn ignition off, and wait 10 seconds. Start vehicle like normal and light should come on and go out like normal. You have reset your SRS light, congrats.

If it does not work the first time try it again, the timing has to be perfect. My first time it took me 3 attempts before it worked, but it did work.

GuateskateVTi
02-Jan-2007, 13:53
ALGO MAS :ok: